Manual mon:
NAME
mon - monitor services for availability, sending alarms upon failures.
SYNOPSIS
mon [-dfhlMSv] [-a dir] [-A authfile] [-b dir] [-B dir] [-c config] [-D dir] [-i secs] [-k num] [-l dir] [-m num] [-p num] [-P pidfile] [-r delay] [-s dir]
DEscRIPTION
mon is a general-purpose scheduler for monitoring service availability and triggering alerts upon detecting failures. mon was designed to be open in the sense that it supports arbitrary monitoring facilities and alert methods via a common interface, which are easily implemented through programs (in C, Perl, shell, etc.), SNMP traps, and special Mon (UDP packet) traps.
OPTIONS
-a dir
Path to alert scripts. Default is /usr/local/lib/mon/alert.d:alert.d. Multiple alert paths may be specified by separating them with a colon. Non-absolute paths are taken to be relative to the base directory (/usr/lib/mon by default).
-b dir
Base directory for mon. scriptdir, alertdir, and statedir are all relative to this directory unless specified from /. Default is /usr/lib/mon.
-B dir
Configuration file base directory. All config files are located here, including mon.cf, monusers.cf, and auth.cf.
-A authfile
Authentication configuration file. By default this is /etc/mon/auth.cf if the /etc/mon directory exists, or /usr/lib/mon/auth. cf otherwise.
-c file
Read configuration from file. This defaults to IR /etc/mon/mon.cf " if the " /etc/mon directory exists, otherwise to /etc/mon.cf.
-d
Enable debugging mode.
-D dir
Path to state directory. Default is the first of /var/state/mon, /var/lib/mon, and /usr/lib/mon/state.d which exists.
-f
Fork and run as a daemon process. This is the preferred way to run mon.
-h
Print help information.
-i secs
Sleep interval, in seconds. Defaults to 1. This shouldn't need to be adjusted for any reason.
-k num
Set log history to a maximum of num entries. Defaults to 100.
-l
Load state from the last saved state file. Currently the only supported saved state is disabled watches, services, and hosts.
-L dir
Sets the log dir. See also logdir in the configuration file. The default is /var/log/mon if that directory exists, otherwise log.d in the base directory.
-M
Pre-process the configuration file with the macro expansion package m4.
-m num
Set the throttle for the maximum number of processes to num.
-p num
Make server listen on port num. This defaults to 2583.
-S
Start with the scheduler stopped.
-P pidfile
Store the server's pid in pidfile, the default is the first of /var/run/mon/mon.pid, /var/run/mon.pid, and /etc/mon.pid whose directory exists. An empty value tells mon not to use a pid file.
-r delay
Sets the number of seconds used to randomize the startup delay before each service is scheduled. Refer to the global randstart variable in the configuration file.
-s dir
Path to monitor scripts. Default is /usr/local/lib/mon/mon.d:mon.d. Multiple alert paths may be specified by separating them with a colon. Non-absolute paths are taken to be relative to the base directory (/usr/lib/mon by default).
-v
Print version information.
DEFINITIONS
monitor
A program which tests for a certain condition, returns either true or false, and optionally produces output to be passed back to the scheduler. Common monitors detect host reachability via ICMP echo messages, or connection to TCP services.
period
A period in time as interpreted by the Time::Period module.
alert
A program which sends a message when invoked by the scheduler. The scheduler calls upon an alert when it detects a failure from a monitor. An alert program accepts a set of command-line arguments from the scheduler, in addition to data via standard input.
hostgroup
A single host or list of hosts, specified as names or IP addresses.
service
A collection of parameters used to deal with monitoring a particular resource which is provided by a group. Services are usually modeled after things such as an SMTP server, ICMP echo capability, server disk space availability, or SNMP events.
watch
A collection of services which apply to a particular group.
OPERATION
When the mon scheduler starts, it reads a configuration file to determine the services it needs to monitor. The configuration file defaults to /etc/mon.cf, and can be specified using the -c parameter. If the -M option is specified, then the configuration file is pre-processed with m4. If the configuration file ends with .m4, the file is also processed by m4 automatically.
The scheduler enters a loop which handles client connections, monitor invocations, and failure alerts. Each service has a timer, specified in the configuration file as the interval variable, which tells the scheduler how frequently to invoke a monitor process. The scheduler may be temporarily stopped. While it is stopped, client access still functions, but it just doesn't schedule things. This is useful in conjunction while resetting the server, because you can do this: save the hosts and services which are disabled, reset the server with the scheduler stopped, re-disabled those hosts and services, then start the scheduler. It also allows making atomic changes across several client connections. See the moncmd man page for more information.
MONITOR PROGRAMS
Monitor processes are invoked with the arguments specified in the configuration file, appended by the hosts from the applicable host group. For example, if the watch group is "servers", which contain the hostnames "smtp", "nntp", and "ns", and the monitor line reads as follows,
monitor fping.monitor -t 4000 -r 2
then the exectuable "fping.monitor" will be executed with these parameters:
MONITOR_DIR/fping.monitor -t 4000 -r 2 smtp nntp ns
MONITOR_DIR is actually a search path, by default /usr/local/lib/mon/mon.d then /usr/lib/mon/mon.d, but it can be overridden by the -s option or in the configuration file. If all hosts in the hostgroup have been disabled, then a warning is sent to syslog and the monitor is not run. This behavior may be overridden with the "allow_empty_group" option in the service definition. If the final argument to the "monitor" line is ";;" (it must be preceded by whitespace), then the host list will not be appended to the parameter list.
In addition to environment variables defined by the user in the service definition, mon passes certain variables to monitor process.
MON_LAST_SUMMARY
The first line of the output from the last time the monitor exited.
MON_LAST_OUTPUT
The entire output of the monitor from the last time it exited.
MON_LAST_FAILURE
The time(2) of the last failure for this service.
MON_FIRST_FAILURE
The time(2) of the first time this service failed.
MON_LAST_SUCCESS
The time(2) of the last time this service passed.
MON_DEscRIPTION
The description of this service, as defined in the configuration file using the description tag.
MON_DEPEND_STATUS
The depend status, "o" if dependency failure, "1" otherwise.
MON_LOGDIR
The directory log files should be placed, as indicated by the logdir global configuration variable.
MON_STATEDIR
The directory where state files should be kept, as indicated by the statedir global configuration variable.
"fping.monitor" should return an exit status of 0 if it completed successfully (found no problems), or nonzero if a problem was detected. The first line of output from the monitor script has a special meaning: it is used as a brief summary of the exact failure which was detected, and is passed to the alert program. All remaining output is also passed to the alert program, but it has no required interpretation.
If a monitor for a particular service is still running, and the time comes for mon to run another monitor for that service, it will not start another monitor. For example, if the interval is 10s, and the monitor does not finish running within 10 seconds, then mon will wait until the first monitor exits before running another one.
ALERT DECISION LOGIC
Upon a non-zero or zero exit status, the associated alert or upalert program (respectively) is started, pending the following conditions: If an alert for a specific service is disabled, do not send an alert. If dep_behavior is set to 'a', and a parent dependency is failing, then suppress the alert. If the alert has previously been acknowledged, do not send the alert, unless it is an upalert. If an alert is not within the specified period, record the failure via syslog(3) and do not send an alert. If the failure does not fall within a defined period, do not send an alert. No upalerts are sent without corresponding down alerts, unless no_comp_alerts is defined in the period section. If an alert was already sent within the last alertevery interval, do not send another alert, unless the summary output from the current monitor program differs from the last monitor process. Otherwise, send an alert using each alert program listed for that period. The observe_detail argument to alertevery affects this behavior by observing the changes in the detail part of the output in addition to the summary line. If a monitor has successive failures and the summary output changes in each of them, alertevery will not suppress multiple consecutive alerts. The reasoning is that if the summary output changes, then a significant event occurred and the user should be alerted.
ALERT PROGRAMS
Alert programs are found in the path supplied with the -a parameter, or in the /usr/local/lib/mon/alert.d and directories if not specified. They are invoked with the following command-line parameters:
-s service
Service tag from the configuration file.
-g group
Host group name from the configuration file.
-h hosts
The expanded version of the host group, space delimited, but contained in one shell "word".
-l alertevery
The number of seconds until the next alarm will be sent.
-O
This option is supplied to an alert only if the alert is being generated as a result of an expected traap timing out
-t time
The time (in time(2) format) of when this failure condition was detected.
-T
This option is supplied to an alert only if the alert was triggered by a trap
-u
This option is supplied to an alert only if it is being called as an upalert.
The remaining arguments are supplied from the trailing parameters in the configuration file, after the "alert" service parameter.
As with monitor programs, alert programs are invoked with environment variables defined by the user in the service definition, in addition to the following which are explicitly set by the server:
MON_LAST_SUMMARY
The first line of the output from the last time the monitor exited.
MON_LAST_OUTPUT
The entire output of the monitor from the last time it exited.
MON_LAST_FAILURE
The time(2) of the last failure for this service.
MON_FIRST_FAILURE
The time(2) of the first time this service failed.
MON_LAST_SUCCESS
The time(2) of the last time this service passed.
MON_DEscRIPTION
The description of this service, as defined in the configuration file using the description tag.
MON_GROUP
The watch group which triggered this alarm
MON_SERVICE
The service heading which generated this alert
MON_RETVAL
The exit value of the failed monitor program, or return value as accepted from a trap.
MON_OPSTATUS
The operational status of the service.
MON_ALERTTYPE
Has one of the following values: "failure", "up", "startup", "trap", or "traptimeout", and signifies the type of alert which was triggered.
MON_TRAP_INTENDED
This is only set when an unknown mon trap is received and caught by the default/defaut watch/service. This contains colon separated entries of the trap's intended watch group and service name.
MON_LOGDIR
The directory log files should be placed, as indicated by the logdir global configuration variable.
MON_STATEDIR
The directory where state files should be kept, as indicated by the statedir global configuration variable.
The first line from standard input must be used as a brief summary of the problem, normally supplied as the subject line of an email, or text sent to an alphanumeric pager. Interpretation of all subsequent lines read from stdin is left up to the alerting program. The usual parameters are a list of recipients to deliver the notification to. The interpretation of the recipients is not specified, and is up to the alert program.
CONFIGURATION FILE
The configuration file consists of zero or more hostgroup definitions, and one or more watch definitions. Each watch definition may have one or more service definitions. A line beginning with optional leading whitespace and a pound ("#") is regarded as a comment, and is ignored.
Lines are parsed as they are read. Long lines may be continued by ending them with a backslash ("\"). If a line is continued, then the backslash, the trailing whitespace after the backslash, and the leading whitespace of the following line are removed. The end result is assembled into a single line.
Global Variables
The following variables may be set to override compiled-in defaults. Command-line options will have a higher precedence than these definitions.
alertdir = dir
dir is the full path to the alert scripts. This is the value set by the -a command-line parameter.
Multiple alert paths may be specified by separating them with a colon. Non-absolute paths are taken to be relative to the base directory (/usr/lib/mon by default).
When the configuration file is read, all alerts referenced from the configuration will be looked up in each of these paths, and the full path to the first instance of the alert found is stored in a hash. This hash is only generated upon startup or after a "reset" command, so newly added alert scripts will not be recognized until a "reset" is performed.
mondir = dir
dir is the full path to the monitor scripts. This value may also be set by the -s command-line parameter.
Multiple alert paths may be specified by separating them with a colon. All paths must be absolute.
When the configuration file is read, all monitors referenced from the configuration will be looked up in each of these paths, and the full path to the first instance of the monitor found is stored in a hash. This hash is only generated upon startup or after a "reset" command, so newly added monitor scripts will not be recognized until a "reset" is performed.
statedir = dir
dir is the full path to the state directory. mon uses this directory to save various state information.
logdir = dir
dir is the full path to the log directory. mon uses this directory to save various logs, including the downtime log.
basedir = dir
dir is the full path for the state, script, and alert directory.
cfbasedir = dir
dir is the full path where all the config files can be found (monusers.cf, auth.cf, etc.).
authfile = file
file is the full path to the authentication file.
authtype = type [type...]
type is the type of authentication to use. A space-separated list of types may be specified, and they will be checked the order they are listed. As soon as a successful authentication is performed, the user is considered authenticated by mon for the duration of the session and no more authentication checks are performed.
If type is getpwnam, then the standard Unix passwd file authentication method will be used (calls getpwnam(3) on the user and compares the crypt(3)ed version of the password with what it gets from getpwnam). This will not work if shadow passwords are enabled on the system.
If type is userfile, then usernames and hashed passwords are read from userfile, which is defined via the userfile configuration variable.
If type is pam, then PAM (pluggable authentication modules) will be used for authentication. The service specified by the pamservice global will be used. If no global is given, the PAM passwd service will be used.
userfile = file
This file is used when authtype is set to userfile. It consists of a sequence of lines of the format 'username : password'. password is stored as the hash returned by the standard Unix crypt(3) function. NOTE: the format of this file is compatible with the Apache file based username/password file format. It is possible to use the htpasswd program supplied with Apache to manage the mon userfile.
Blank lines and lines beginning with # are ignored.
pamservice = service
The PAM service used for authentication. This is applicable only if "pam" is specified as a parameter to the authtype setting. If this global is not defined, it defaults to passwd.
snmpport = portnum
Set the SNMP port that the server binds to.
serverbind = addr
trapbind = addr
serverbind and trapbind specify which address to bind the server and trap ports to, respectively. If these are not defined, the default address is INADDR_ANY, which allows connections on all interfaces. For security reasons, it could be a good idea to bind only to the loopback interface.
snmp ={yes|no}
Turn on/off SNMP support (currently unimplemented).
dtlogfile = file
file is a file which will be used to record the downtime log. Whenever a service fails for some amount of time and then stop failing, this event is written to the log. If this parameter is not set, no logging is done. The format of the file is as follows (# is a comment and may be ignored):
timenoticed group service firstfail downtime interval summary.
timenoticed is the time(2) the service came back up.
group service is the group and service which failed.
firstfail is the time(2) when the service began to fail.
downtime is the number of seconds the service failed.
interval is the frequency (in seconds) that the service is polled.
summary is the summary line from when the service was failing.
dtlogging = yes/no
Turns downtime logging on or off. The default is off.
histlength = num
num is the the maximum number of events to be retained in history list. The default is 100. This value may also be set by the -k command-line parameter.
historicfile = file
If this variable is set, then alerts are logged to file, and upon startup, some (or all) of the past history is read into memory.
historictime = timeval
num is the amount of the history file to read upon startup. "Now" - timeval is read. See the explanation of interval in the "Service Definitions" section for a description of timeval.
serverport = port
port is the TCP port number that the server should bind to. This value may also be set by the -p command-line parameter. Normally this port is looked up via getservbyname(3), and it defaults to 2583.
trapport = port
port is the UDP port number that the trap server should bind to. Normally this port is looked up via getservbyname(3), and it defaults to 2583.
pidfile = path
path is the file the sever will store its pid in. This value may also be set by the -P command-line parameter.
maxprocs = num
Throttles the number of concurrently forked processes to num. The intent is to provide a safety net for the unlikely situation when the server tries to take on too many tasks at once. Note that this situation has only been reported to happen when trying to use a garbled configuration file! You don't want to use a garbled configuration file now, do you?
cltimeout = secs
Sets the client inactivity timeout to secs. This is meant to help thwart denial of service attacks or recover from crashed clients. secs is interpreted as a "1h/1m/1s" string, where "1m" = 60 seconds.
randstart = interval
When the server starts, normally all services will not be scheduled until the interval defined in the respective service section. This can cause long delays before the first check of a service, and possibly a high load on the server if multiple things are scheduled at the same intervals. This option is used to randomize the scheduling of the first test for all services during the startup period, and immediately after the reset command. If randstart is defined, the scheduled run time of all services of all watch groups will be a random number between zero and randstart seconds.
dep_recur_limit = depth
Limit dependency recursion level to depth. If dependency recursion (dependencies which depend on other dependencies) tries to go beyond depth, then the recursion is aborted and a messages is logged to syslog. The default limit is 10.
dep_behavior = {a|m}
dep_behavior controls whether the dependency expression suppresses either the running of alerts or monitors when a node in the dependency graph fails. Read more about the behavior in the "Service Definitions" section below.
This is a global setting which controls the default settings for the service-specified variable.
syslog_facility = facility
Specifies the syslog facility used for logging. daemon is the default.
startupalerts_on_reset = {yes|no}
If set to "yes", startupalerts will be invoked when the reset client command is executed. The default is "no".
Hostgroup Entries
Hostgroup entries begin with the keyword hostgroup, and are followed by a hostgroup tag and one or more hostnames or IP addresses, separated by whitespace. The hostgroup tag must be composed of alphanumeric characters, a dash ("-"), a period ("."), or an underscore ("_"). Non-blank lines following the first hostgroup line are interpreted as more hostnames. The hostgroup definition ends with a blank line. For example:
hostgroup servers nameserver smtpserver nntpserver
nfsserver httpserver smbserver
hostgroup router_group cisco7000 agsplus
Watch Group Entries
Watch entries begin with a line that starts with the keyword watch, followed by whitespace and a single word which normally refers to a pre-defined hostgroup. If the second word is not recognized as a hostgroup tag, a new hostgroup is created whose tag is that word, and that word is its only member.
Watch entries consist of one or more service definitions.
There is a special watch group entry called "default". If a default watch group is defined with a "default" service entry, then this definition will be used in handling unknown mon traps.
Service Definitions
service servicename
A service definition begins with they keyword service followed by a word which is the tag for this service.
The components of a service are an interval, monitor, and one or more time period definitions, as defined below.
If a service name of "default" is defined within a watch group called "dafault" (see above), then the default/default definition will be used for handling unknown mon traps.
interval timeval
The keyword interval followed by a time value specifies the frequency that a monitor script will be triggered. Time values are defined as "30s", "5m", "1h", or "1d", meaning 30 seconds, 5 minutes, 1 hour, or 1 day. The numeric portion may be a fraction, such as "1.5h" or an hour and a half. This format of a time specification will be referred to as timeval.
traptimeout timeval
This keyword takes the same time specification argument as interval, and makes the service expect a trap from an external source at least that often, else a failure will be registered. This is used for a heartbeat-style service.
trapduration timeval
If a trap is received, the status of the service the trap was delivered to will normally remain constant. If trapduration is specified, the status of the service will remain in a failure state for the duration specified by timeval, and then it will be reset to "success".
randskew timeval
Rather than schedule the monitor script to run at the start of each interval, randomly adjust the interval specified by the interval parameter by plus-or-minus randskew. The skew value is specified as the interval parameter: "30s", "5m", etc... For example if interval is 1m, and randskew is "5s", then mon will schedule the monitor script some time between every 55 seconds and 65 seconds. The intent is to help distribute the load on the server when many services are scheduled at the same intervals.
monitor monitor-name [arg...]
The keyword monitor followed by a script name and arguments specifies the monitor to run when the timer expires. Shell-like quoting conventions are followed when specifying the arguments to send to the monitor script. The script is invoked from the directory given with the -s argument, and all following words are supplied as arguments to the monitor program, followed by the list of hosts in the group referred to by the current watch group. If the monitor line ends with ";;" as a separate word, the host groups are not appended to the argument list when the program is invoked.
allow_empty_group
The allow_empty_group option will allow a monitor to be invoked even when the hostgroup for that watch is empty because of disabled hosts. The default behavior is not to invoke the monitor when all hosts in a hostgroup have been disabled.
description descriptiontext
The text following description is queried by client programs, passed to alerts and monitors via an environment variable. It should contain a brief description of the service, suitable for inclusion in an email or on a web page.
exclude_hosts host [host...]
Any hosts listed after exclude_hosts will be excluded from the service check.
exclude_period periodspec
Do not run a scheduled monitor during the time identified by periodspec.
depend dependexpression
The depend keyword is used to specify a dependency expression, which evaluates to either true of false, in the boolean sense. Dependencies are actual Perl expressions, and must obey all syntactical rules. The expressions are evaluated in their own package space so as to not accidentally have some unwanted side-effect. If a syntax error is found when evaluating the expression, it is logged via syslog.
Before evaluation, the following substitutions on the expression occur: phrases which look like "group:service" are substituted with the value of the current operational status of that specified service. These opstatus substitutions are computed recursively, so if service A depends upon service B, and service B depends upon service C, then service A depends upon service C. Successful operational statuses (which evaluate to "1") are "STAT_OK", "STAT_COLDSTART", "STAT_WARMSTART", and "STAT_UNKNOWN". The word "SELF" (in all caps) can be used for the group (e.g. "SELF:service"), and is an abbreviation for the current watch group.
This feature can be used to control alerts for services which are dependent on other services, e.g. an SMTP test which is dependent upon the machine being ping-reachable.
dep_behavior {a|m}
The evaluation of dependency graphs can control the suppression of either alert or monitor invocations.
Alert suppression. If this option is set to "a", then the dependency expression will be evaluated after the monitor for the service exits or after a trap is received. An alert will only be sent if the evaluation succeeds, meaning that none of the nodes in the dependency graph indicate failure.
Monitor suppression. If it is set to "m", then the dependency expression will be evaulated before the monitor for the service is about to run. If the evaulation succeeds, then the monitor will be run. Otherwise, the monitor will not be run and the status of the service will remain the same.
Period Definitions
Periods are used to define the conditions which should allow alerts to be delivered.
period [label:] periodspec
A period groups one or more alarms and variables which control how often an alert happens when there is a failure. The period keyword has two forms. The first takes an argument which is a period specification from Patrick Ryan's Time::Period Perl 5 module. Refer to "perldoc Time::Period" for more information.
The second form requires a label followed by a period specification, as defined above. The label is a tag consisting of an alphabetic character or underscore followed by zero or more alphanumerics or underscores and ending with a colon. This form allows multiple periods with the same period definition. One use is to have a period definition which has no alertafter or alertevery parameters for a particular time period, and another for the same time period with a different set of alerts that does contain those parameters.
alertevery timeval [observe_detail]
The alertevery keyword (within a period definition) takes the same type of argument as the interval variable, and limits the number of times an alert is sent when the service continues to fail. For example, if the interval is "1h", then only the alerts in the period section will only be triggered once every hour. If the alertevery keyword is omitted in a period entry, an alert will be sent out every time a failure is detected. By default, if the summary output of two successive failures changes, then the alertevery interval is overridden, and an alert will be sent. If the string "observe_detail" is the last argument, then both the summary and detail output lines will be considered when comparing the output of successive failures. Please refer to the ALERT DECISION LOGIC section for a detailed explanation of how alerts are suppressed.
alertafter num
alertafter num timeval
alertafter timeval
The alertafter keyword (within a period section) has three forms: only with the "num" argument, or with the "num timeval" arguments, or only with the "timeval" argument. In the first form, an alert will only be invoked after "num" consecutive failures.
In the second form, the arguments are a positive integer followed by an interval, as described by the interval variable above. If these parameters are specified, then the alerts for that period will only be called after that many failures happen within that interval. For example, if alertafter is given the arguments "3 30m", then the alert will be called if 3 failures happen within 30 minutes.
In the third form, the argument is an interval, as described by the interval variable above. Alerts for that period will only be called if the service has been in a failure state for more than the length of time desribed by the interval, regardless of the number of failures noticed within that interval.
numalerts num
This variable tells the server to call no more than num alerts during a failure. The alert counter is kept on a per-period basis, and is reset upon each success.
no_comp_alerts
If this option is specified, then upalerts will be called whenever the service state changes from failure to success, rather than only after a corresponding "down" alert.
alert alert [arg...]
A period may contain multiple alerts, which are triggered upon failure of the service. An alert is specified with the alert keyword, followed by an optional exit parameter, and arguments which are interpreted the same as the monitor definition, but without the ";;" exception. The exit parameter takes the form of exit=x or exit=x-y and has the effect that the alert is only called if the exit status of the monitor script falls within the range of the exit parameter. If, for example, the alert line is alert exit=10-20 mail.alert mis then mail-alert will only be invoked with mis as its arguments if the monitor program's exit value is between 10 and 20. This feature allows you to trigger different alerts at different severity levels (like when free disk space goes from 8% to 3%).
See the ALERT PROGRAMS section above for a list of the pramaeters mon will pass automatically to alert programs.
failure_interval timeval
Adjusts the polling interval to timeval when the service check is failing. Resets the interval to the original when the service succeeds.
upalert alert [arg...]
An upalert is the compliment of an alert. An upalert is called when a services makes the state transition from failure to success, if a corresponding "down" alert was previously sent. The upalert script is called supplying the same parameters as the alert script, with the addition of the -u parameter which is simply used to let an alert script know that it is being called as an upalert. Multiple upalerts may be specified for each period definition. Set the per-period no_comp_alerts option to send an upalert regardless if whether or not a "down" alert was sent.
startupalert alert [arg...]
A startupalert is only called when the mon server starts execution.
upalertafter timeval
The upalertafter parameter is specified as a string that follows the syntax of the interval parameter ("30s", "1m", etc.), and controls the triggering of an upalert. If a service comes back up after being down for a time greater than or equal to the value of this option, an upalert will be called. Use this option to prevent upalerts to be called because of "blips" (brief outages).
AUTHENTICATION CONFIGURATION FILE
The file specified by the authfile variable in the configuration file (or passed via the -A parameter) will be loaded upon startup. This file defines restrictions upon which client commands may be executed by which users. It is a text file which consists of comments, command definitions, and trap authentication parameters. A comment line begins with optional whitespace followed by pound sign. Blank lines are ignored.
The file is separated into a command section and a trap section. Sections are specified by a single line containing one of the following statements:
command section
or
trap section
Lines following one of the above statements apply to that section until either the end of the file or another section begins.
A command definition consists of a command, followed by a colon, followed by a comma-separated list of users who may execute the command. The default is that no users may execute any commands unless they are explicitly allowed in this configuration file. For clarity, a user can be denied by prefixing the user name with "!". If the word "AUTH_ANY" is used for a username, then any authenticated user will be allowed to execute the command.
The trap section allows configuration of which users may send traps from which hosts. The syntax is a source host (name or ip address), whitespace, a username, whitespace, and a plaintext password for that user. If the source host is "*", then allow traps from any host. If the username is "*", then accept traps without regard for the username or password. If no hosts or users are specified, then no traps will be accepted.
An example configuration file:
command section
list: all
reset: root,admin
loadstate: root
savestate: root
trap section
127.0.0.1 root r@@tp4sswrd
This means that all clients are able to perform the list command, "root" is able to perform "reset", "loadstate", "savestate", and "admin" is able to execute the "reset" command.
CLIENT-SERVER INTERFACE
The server listens on TCP port 2583, which may be overridden using the -p port option. Commands are a single line each, terminated by a newline. Currently the server is iterative, accepting a single client at a time. This will change in future releases.
CLIENT INTERFACE COMMANDS
See manual page for moncmd.
MON TRAPPING
Mon has the facility to receive special "mon traps" from any local or remote machine. Currently, the only available method for sending mon traps are through the Mon::Client perl interface, though the UDP packet format is defined well enough to permit the writing of traps in other languages.
Traps are handled similarly to monitors: a trap sends an operational status, summary line, and description text, and mon generates an alert or upalert as necessary.
Traps can be caught by any watch/service group set up in the mon configuration file, however it is suggested that you configure watch/service groups specifically for the traps you expect to receive. When defining a special watch/service group for traps, do not include a "monitor" directive (as no monitor need be invoked). Since a monitor is not being invoked, it is not necessary for the watch definition to have a hostgroup which contains real host names. Just make up a useful name, and mon will automatically create the watch group for you.
Here is a simple config file example:
watch trap-service
service host1-disks
description TRAP: for host1 disk status
period wd {Sun-Sat}
alert mail.alert someone@your.org
upalert mail.alert -u someone@your.org
Since mon listens on a UDP port for any trap, a default facility is available for handling traps to unknown groups or services. To enable this facility, you must include a "default" watch group with a "default" service entry containing the specifics of alarms. If a default/default watch group and service are not configured, then unknown traps get logged via syslog, and no alarm is sent. NOTE: The default/default facility is a single entity as far as accounting and alarming go. Alarm programs which are not aware of this fact may send confusing information when a failure trap comes from one machine, followed by a success (ok) trap from a different machine. See the alarm environment variable MON_TRAP_INTENDED above for a possible way around this. It is intended that default/default be used as a facility to catch unknown traps, and should not be relied upon to catch all traps in a production environment. If you are lazy and only want to use default/default for catching all traps, it would be best to disable upalerts, and use the MON_TRAP_INTENDED environment variable in alert scripts to make the alerts more meaningful to you.
Here is an example default facility:
watch default
service default
description Default trap service
period wd {Sun-Sat}
alert mail.alert someone@your.org
upalert mail.alert -u someone@your.org
EXAMPLES
The mon distribution comes with an example configuration called example.cf. Refer to that file for more information.
SEE ALSO
moncmd(1), Time::Period(3pm), Mon::Client(3pm)
HISTORY
mon was written because I couldn't find anything out there that did just what I needed, and nothing was worth modifying to add the features I wanted. It doesn't have a cool name, and that bothers me because I couldn't think of one.
BUGS
Report bugs to the email address below.
AUTHOR
Jim Trocki trockij@transmeta.com