traceroute°¡»ç¿ëÇÏ´Â ¿ø¸®´Â µ¿ÀÏÇÏÁö¸¸ ±¸Çö¹æ¹ýÀº ½Ã½ºÅÛ¿¡ µû¶ó Â÷ÀÌÁ¡ÀÌ ÀÖÀ¸¸ç, ÀϹÝÀûÀÎ Unix °è¿¹× cisco °è¿ ¶ó¿ìÅÍÀÇ °æ¿ì ¸ñÀûÁö ½Ã½ºÅÛÀÇ 33434~38000 Æ÷Æ®·Î TTL °ªÀ» 1¾¿ ´Ã·Á°¡¸é¼ udp ÆÐŶÀ» ¹ß¼ÛÇÏ¿© TTL °ªÀǸ¸±â(expiration)·Î ÀÎÇÏ¿© µ¹¾Æ¿À´Â "ICMP time exceed" ¸Þ½ÃÁö¸¦ ÀÌ¿ëÇÕ´Ï´Ù.
¹Ý¸é Windows °è¿ÀÇ
tracert ´Â ¸ñÀûÁö ½Ã½ºÅÛ¿¡ TTL°ªÀ» 1¾¿ ´Ã·Á°¡¸é¼ ICMP echo request ÆÐŶÀ» ¹ß¼ÛÇÏ¿© ¿ª½Ã TTL °ªÀÇ ¸¸±â·Î µ¹¾Æ¿À´Â "ICMP time exceed" ¸Þ½ÃÁö¸¦ ÀÌ¿ëÇÕ´Ï´Ù
¡Ø traceroute ¿É¼Ç
OPTIONS
The only required parameter is the name or IP address of the destination host. This paremeter can be followed by the size of the probing packet sent to that host (40 by
default). Varying the size of the packet in conjunction with the -F parameter can be used to obtain information about the MTU of individual network hops. (The size parameter
is useless for TCP probes).
Additional options are:
--help Print help info and exit.
-4, -6 Explicitly force IPv4 or IPv6 traceouting. By default, the program will try to resolve the name given, and choose the appropriate protocol automatically. If resolving a host name returns both IPv4 and IPv6 addresses, traceroute will use IPv4.
-I Use ICMP ECHO for probes
-T Use TCP SYN for probes
-U Use UDP datagrams for probes (it is default). Only UDP method is allowed for unprivileged users.
-d Enable socket level debugging (when the Linux kernel supports it)
-F Set the "Don¡¯t Fragment" bit. This tells intermediate routers not to fragment the packet when they find it¡¯s too big for a network hop¡¯s MTU.
-f first_ttl
Specifies with what TTL to start. Defaults to 1.
-g gateway
Tells traceroute to add an IP source routing option to the outgoing packet that tells the network to route the packet through the specified gateway. Not very useful,
because most routers have disabled source routing for security reasons.
-i interface
Specifies the interface through which traceroute should send packets. By default, the interface is selected according to the routing table.
-m max_ttl
Specifies the maximum number of hops (max time-to-live value) traceroute will probe. The default is 30.
-N squeries
Specifies the number of probe packets sent out simultaneously. Sending several probes concurrently can speed up traceroute considerably. The default value is 16.
Note that some routers and hosts can use ICMP rate throttling. In such a situation specifying too large number can lead to loss of some responses.
-n Do not try to map IP addresses to host names when displaying them.
-p port
For UDP tracing, specifies the destination port base traceroute will use (the destination port number will be incremented by each probe).
For ICMP tracing, specifies the initial icmp sequence value (incremented by each probe too).
For TCP specifies just the (constant) destination port to connect.
-t tos For IPv4, set the Type of Service (TOS) and Precedence value. Useful values are 16 (low delay) and 8 (high throughput). Note that in order to use some TOS precendence
values, you have to be super user.
For IPv6, set the Traffic Control value.
-w waittime
Set the time (in seconds) to wait for a response to a probe (default 5.0 sec).
-q nqueries
Sets the number of probe packets per hop. The default is 3.
-r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached network, an error is returned. This
option can be used to ping a local host through an interface that has no route through it.
-s source_addr
Chooses an alternative source address. Note that you must select the address of one of the interfaces. By default, the address of the outgoing interface is used.
-z sendwait
Minimal time interval between probes (default 0). If the value is more than 10, then it specifies a number in milliseconds, else it is a number of seconds (float
point values allowed too). Useful when some routers use rate-limit for icmp messages.
-A Perform AS path lookups in routing registries and print results directly after the corresponding addresses
-V Print the version and exit.